Electric Counterbalance Forklift Procurement Checklist: Verifying Battery Bank Capacity, Charger Sizing, and Site Power Readiness
News 08/11/2026
Buying an electric counterbalance forklift means buying an energy system as well as a truck. The battery bank, charger, and site electrical supply must agree with each other and with the duty cycle. A mismatch usually appears as short runtimes, long charging windows, or charger faults during peak hours—problems that surface after delivery, not in the quotation. This checklist sets out the documents and figures a buyer should collect before placing an order, with the four-wheel counterbalance electric forklift as the working assumption.
Start with the duty cycle, not the battery label
Battery capacity only means something when paired with a workload. Before comparing ampere-hour ratings, record the following:
- Shift length and number of shifts per day, including breaks when the truck is idle.
- Load weight and load center distance in normal use, plus the heaviest load handled.
- Required lift height and how often loads reach that height.
- Travel distance per shift and floor conditions, including ramps and gradients.
- Attachment type, since a side-shifter or clamp adds weight and changes the load chart.
These figures let a supplier match a battery and charger combination to real demand. They also reveal whether one battery per truck is workable or whether opportunity charging or a battery change is needed. Without this data, any capacity figure in a quotation is an assumption.
Battery bank capacity: what to verify in the offer
Ask the supplier to state the battery voltage, rated capacity in ampere-hours, and the discharge rate at which that capacity is defined. Capacity ratings are not interchangeable across different discharge rates, so the basis must be written down. Confirm the chemistry as well: lithium-ion packs and lead-acid batteries have different charging behavior, maintenance needs, and usable depth of discharge, and the charger must match the chemistry.
Also request the physical dimensions and weight of the pack, the compartment it fits, and the counterweight implications. On a four-wheel counterbalance electric forklift the battery contributes to stability, so a replacement pack of different weight or position is not a neutral swap. Where the manufacturer publishes a load chart, check that the intended battery configuration is the one the chart assumes.

Questions to put to the supplier
- Which battery configuration does the quoted load chart assume?
- What runtime does the supplier expect under the duty cycle you described, and on what basis?
- Is opportunity charging supported, and what limits apply?
- What maintenance or monitoring does the pack require, and who performs it?
Treat expected runtime as an estimate until the supplier states its assumptions. If no figure can be supported, plan a trial period and agree in advance how runtime will be measured.
Charger sizing and site power readiness
Charger selection follows from the battery: voltage, chemistry, and the acceptable recharge window. A charger that is too small extends charging beyond the available window; one that is oversized may exceed the capacity of the site supply. Ask for the charger input voltage, input current, output profile, connector type, and the recharge time it implies for the quoted pack.
Site power deserves the same scrutiny. A common procurement error is to approve a charger before checking the building supply. Verify the following with the facility electrician or utility, since only they can confirm local capacity and code compliance:

| Item to confirm | Why it matters |
|---|---|
| Available supply voltage and phase | Must match the charger input rating |
| Spare capacity at the charging area | Prevents overload when other equipment runs |
| Charging position and ventilation | Affects installation and, with lead-acid, gas handling |
| Cable route and connector reach | Determines whether trucks can park and plug in safely |
| Charging schedule versus peak tariffs | Influences when charging can realistically occur |
Where the supply is constrained, the practical options are a lower-power charger with longer windows, scheduled charging outside peak periods, or a different charging strategy. Each changes the operating routine, so agree it before delivery rather than after.
Acceptance points on delivery
- Battery and charger nameplate data match the purchase order and the load chart.
- Charger completes a full cycle within the agreed window, measured on site.
- Connectors, cables, and charging position meet the agreed layout.
- Operators receive handover on charging procedure and daily checks.
Frequently asked questions
Can I reuse an existing charger with a new lithium-ion pack?
Only if the charger is configured and rated for that chemistry and voltage. Reusing a lead-acid charger without confirmation risks incorrect charging and may void warranties. Ask the battery and charger suppliers to confirm compatibility in writing.
Is a larger battery always the safer choice?
Not necessarily. A larger pack adds weight and cost and may not fit the compartment or the load chart assumptions. Match capacity to the measured duty cycle, and confirm the configuration against the manufacturer’s documentation.

What if the site supply cannot support the recommended charger?
Discuss derated charging, scheduled charging, or a revised operating plan with the supplier and the facility electrician. The right answer depends on shift patterns and the building’s electrical capacity, which only local verification can establish.
Which documents should accompany the quotation?
Request the load chart, battery specification, charger specification, and installation requirements. If you are evaluating a four-wheel counterbalance electric forklift, share your load, lift height, shift pattern, and charging area details so the configuration can be checked against them.



